Xiaomi Mi Router 3 — глубокий анбоксинг

Опубликовал | 04.06.2016

  • Цена: 29.99$

Кcтaти, xoчу cрaзу oтмeтить oдну cтрaннocть: мoй экзeмпляр нe имeeт рaдиaтoрa нa цeнтрaльнoм прoцeccoрe!

Иcпытaния

Рoутeр у мeня зaвeлcя c пoл пинкa:

Для нaчaлa я пoдключил к UART-пoрту рoутeрa cвoю любимую Arduino Due и cнял лoги:

Пoлный лoг-зaгрузки
  U-Boot 1.1.3 (Mar 16 2016 - 14:15:12)    Board: Ralink APSoC DRAM:  128 MB  Power on memory test. Memory size= 128 MB...OK!  relocate_code Pointer at: 87fb8000  enable ephy clock...done. rf reg 29 = 5  SSC disabled.  !!! nand page size = 2048, addr len=4  ..============================================  Ralink UBoot Version: 4.2.S.1  --------------------------------------------  ASIC 7620_MP (Port5<->None)  DRAM_CONF_FROM: Auto-detection  DRAM_TYPE: DDR2  DRAM component: 1024 Mbits  DRAM bus: 16 bit  Total memory: 128 MBytes  Flash component: NAND Flash  Date:Mar 16 2016  Time:14:15:12  ============================================  icache: sets:512, ways:4, linesz:32 ,total:65536  dcache: sets:256, ways:4, linesz:32 ,total:32768     ##### The CPU freq = 580 MHZ ####   estimate memory size =128 Mbytes    Please choose the operation:     1: Load system code to SDRAM via TFTP.     2: Load system code then write to Flash via TFTP.     3: Boot system code via Flash (default).     4: Entr boot command line interface.     9: Load Boot Loader code then write to Flash via TFTP.      3: System Boot system code via Flash.  Booting System 1  ..Erasing NAND Flash...  Writing to NAND Flash...  done  ## Booting image at bc200000 ...     Image Name:   MIPS OpenWrt Linux-2.6.36     Image Type:   MIPS Linux Kernel Image (lzma compressed)     Data Size:    2616754 Bytes =  2.5 MB     Load Address: 80000000     Entry Point:  80000000  ........................................   Verifying Checksum ... OK     Uncompressing Kernel Image ... OK  commandline uart_en=0 factory_mode=0 mem=128m  No initrd  ## Transferring control to Linux (at address 80000000) ...  ## Giving linux memsize in MB, 128    Starting kernel ...      LINUX started...     THIS IS ASIC  [    0.000000] Initializing cgroup subsys cpuset  [    0.000000] Initializing cgroup subsys cpu  [    0.000000] Linux version 2.6.36 (jenkins@JenkinsServer) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Wed Mar 16 14:27:38 CST 2016  [    0.000000]  [    0.000000]  The CPU feqenuce set to 580 MHz  [    0.000000]  PCIE: bypass PCIe DLL.  [    0.000000]  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4  [    0.000000]  disable all power about PCIe  [    0.000000] CPU revision is: 00019650 (MIPS 24Kc)  [    0.000000] Software DMA cache coherency  [    0.000000] Determined physical RAM map:  [    0.000000]  memory: 08000000 @ 00000000 (usable)  [    0.000000] User-defined physical RAM map:  [    0.000000]  memory: 08000000 @ 00000000 (usable)  [    0.000000] Initrd not found or empty - disabling initrd  [    0.000000] Zone PFN ranges:  [    0.000000]   Normal   0x00000000 -> 0x00008000  [    0.000000] Movable zone start PFN for each node  [    0.000000] early_node_map[1] active PFN ranges  [    0.000000]     0: 0x00000000 -> 0x00008000  [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512  [    0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 uart_en=0 factory_mode=0 mem=128m  [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)  [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)  [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)  [    0.000000] Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.  [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes  [    0.000000] Writing ErrCtl register=0005a42b  [    0.000000] Readback ErrCtl register=0005a42b  [    0.000000] allocated 655360 bytes of page_cgroup  [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups  [    0.000000] Memory: 123440k/131072k available (3347k kernel code, 7632k reserved, 1029k data, 1188k init, 0k highmem)  [    0.000000] SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1  [    0.000000] NR_IRQS:128  [    0.000000] console [ttyS1] enabled  [    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)  [    0.220000] pid_max: default: 32768 minimum: 301  [    0.220000] Mount-cache hash table entries: 512  [    0.220000] Initializing cgroup subsys cpuacct  [    0.230000] Initializing cgroup subsys memory  [    0.230000] Initializing cgroup subsys net_cls  [    0.230000] devtmpfs: initialized  [    0.240000] NET: Registered protocol family 16  [    0.240000] RALINK_GPIOMODE = 121b1c  [    0.240000] RALINK_GPIOMODE = 101b1c  [    0.440000] PPLL_CFG1=0xe64000  [    0.450000] MT7620 PPLL lock  [    0.450000] PPLL_DRV =0x80080504  [    0.650000]  Deassert the PCIE0 RESET.  [    0.650000] start PCIe register access  [    1.150000] RALINK_RSTCTRL = 2400000  [    1.160000] RALINK_CLKCFG1 = 75afffc0  [    1.160000]  [    1.160000] *************** MT7620 PCIe RC mode *************  [    1.660000] PCIE0 enabled  [    1.670000] init_rt2880pci done  [    1.670000] bio: create slab <bio-0> at 0  [    1.680000] SCSI subsystem initialized  [    1.680000] usbcore: registered new interface driver usbfs  [    1.680000] usbcore: registered new interface driver hub  [    1.690000] usbcore: registered new device driver usb  [    1.690000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)  [    1.700000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]  [    1.700000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]  [    1.710000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]  [    1.710000] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]  [    1.720000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]  [    1.720000] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]  [    1.730000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]  [    1.730000] pci 0000:00:00.0: PCI bridge to [bus 01-01]  [    1.740000] pci 0000:00:00.0:   bridge window [io  disabled]  [    1.740000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]  [    1.750000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]  [    1.750000] BAR0 at slot 0 = 0  [    1.760000] bus=0x0, slot = 0x0  [    1.760000] res[0]->start = 0  [    1.760000] res[0]->end = 0  [    1.760000] res[1]->start = 20200000  [    1.770000] res[1]->end = 2020ffff  [    1.770000] res[2]->start = 0  [    1.770000] res[2]->end = 0  [    1.770000] res[3]->start = 0  [    1.780000] res[3]->end = 0  [    1.780000] res[4]->start = 0  [    1.780000] res[4]->end = 0  [    1.780000] res[5]->start = 0  [    1.790000] res[5]->end = 0  [    1.790000] bus=0x1, slot = 0x0  [    1.790000] res[0]->start = 20000000  [    1.790000] res[0]->end = 200fffff  [    1.800000] res[1]->start = 0  [    1.800000] res[1]->end = 0  [    1.800000] res[2]->start = 0  [    1.800000] res[2]->end = 0  [    1.810000] res[3]->start = 0  [    1.810000] res[3]->end = 0  [    1.810000] res[4]->start = 0  [    1.810000] res[4]->end = 0  [    1.820000] res[5]->start = 0  [    1.820000] res[5]->end = 0  [    1.820000] Switching to clocksource MIPS  [    1.830000] NET: Registered protocol family 2  [    1.830000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)  [    1.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)  [    1.850000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)  [    1.850000] TCP: Hash tables configured (established 4096 bind 4096)  [    1.860000] TCP reno registered  [    1.860000] UDP hash table entries: 256 (order: 0, 4096 bytes)  [    1.870000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)  [    1.870000] NET: Registered protocol family 1  [    3.280000] RT3xxx EHCI/OHCI init.  [    3.290000] msgmni has been set to 241  [    3.290000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)  [    3.300000] io scheduler noop registered (default)  [    3.310000] RALINK_REG_PIO7140DATA b0000670 = 0  [    3.410000] RALINK_REG_PIO7140DATA b0000670 = 2000000  [    3.420000] Ralink gpio driver initialized  [    3.420000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled  [    3.430000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A  [    3.430000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A  [    3.440000] init reset module!  [    3.450000] brd: module loaded  [    3.450000] !!! nand page size = 2048, addr len=4  [    3.460000] ra_nand_init: alloc 1350, at 87d90000 , btt(87d910c0, 100), ranfc_mtd:87d911c0  [    3.470000] Creating 13 MTD partitions on "ra_nfc":  [    3.470000] 0x000000000000-0x000008000000 : "ALL"  [    3.500000] 0x000000000000-0x000000040000 : "Bootloader"  [    3.510000] 0x000000040000-0x000000080000 : "Config"  [    3.510000] 0x000000080000-0x0000000c0000 : "Bdata"  [    3.520000] 0x0000000c0000-0x000000100000 : "Factory"  [    3.530000] 0x000000100000-0x000000140000 : "crash"  [    3.530000] 0x000000140000-0x000000180000 : "crash_syslog"  [    3.540000] 0x000000180000-0x000000200000 : "reserved0"  [    3.540000] 0x000000200000-0x000000600000 : "kernel0"  [    3.550000] 0x000000600000-0x000000a00000 : "kernel1"  [    3.560000] 0x000000a00000-0x000002a00000 : "rootfs0"  [    3.560000] 0x000002a00000-0x000004a00000 : "rootfs1"  [    3.570000] 0x000004a00000-0x000008000000 : "overlay"  [    3.570000] rdm_major = 253  [    3.580000] SMACCR1 -- : 0x00006409  [    3.580000] SMACCR0 -- : 0x8068a794  [    3.580000] Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!  [    3.590000] SMACCR1 -- : 0x00006409  [    3.600000] SMACCR0 -- : 0x8068a794  [    3.600000] PROC INIT OK!  [    3.610000] PPP generic driver version 2.4.2  [    3.610000] PPP MPPE Compression module registered  [    3.620000] NET: Registered protocol family 24  [    3.620000] PPTP driver version 0.8.5  [    3.630000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver  [    3.750000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller  [    3.760000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1  [    3.800000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000  [    3.820000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00  [    3.820000] hub 1-0:1.0: USB hub found  [    3.830000] hub 1-0:1.0: 1 port detected  [    3.830000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver  [    3.860000] rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller  [    3.860000] rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2  [    3.870000] rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000  [    3.940000] hub 2-0:1.0: USB hub found  [    3.940000] hub 2-0:1.0: 1 port detected  [    3.950000] usbcore: registered new interface driver cdc_acm  [    3.950000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters  [    3.960000] Initializing USB Mass Storage driver...  [    3.970000] usbcore: registered new interface driver usb-storage  [    3.970000] USB Mass Storage support registered.  [    3.980000] usbcore: registered new interface driver usbserial  [    3.980000] USB Serial support registered for generic  [    3.990000] usbcore: registered new interface driver usbserial_generic  [    4.000000] usbserial: USB Serial Driver core  [    4.000000] USB Serial support registered for pl2303  [    4.010000] usbcore: registered new interface driver pl2303  [    4.010000] pl2303: Prolific PL2303 USB to serial adaptor driver  [    4.020000] USB Serial support registered for TI USB 3410 1 port adapter  [    4.030000] USB Serial support registered for TI USB 5052 2 port adapter  [    4.030000] usbcore: registered new interface driver ti_usb_3410_5052  [    4.040000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver  [    4.050000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)  [    4.050000] u32 classifier  [    4.060000]     input device check on  [    4.060000]     Actions configured  [    4.060000] Netfilter messages via NETLINK v0.30 with ipset netlink.patch.  [    4.070000] nf_conntrack version 0.5.0 (1928 buckets, 7712 max)  [    4.080000] xt_time: kernel timezone is -0000  [    4.080000] GRE over IPv4 demultiplexor driver  [    4.090000] ip_tables: © 2000-2006 Netfilter Core Team, Type=Restricted Cone  [    4.100000] TCP cubic registered  [    4.100000] NET: Registered protocol family 10  [    4.110000] NET: Registered protocol family 17  [    4.110000] L2TP core driver, V2.0  [    4.110000] PPPoL2TP kernel driver, V2.0  [    4.120000] L2TP netlink interface  [    4.120000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>  [    4.130000] All bugs added by David S. Miller <davem@redhat.com>  [    4.150000] Freeing unused kernel memory: 1188k freed  [    4.240000] Loading essential drivers...  [    4.250000] Press Ctrl+C to enter RAMFS...  [    5.260000] Check for USB recovery...  [    5.290000] Bringup the system...  [    5.300000] flag_boot_rootfs=0 mounting /dev/mtd10  [    5.310000] UBI: attaching mtd10 to ubi0  [    5.310000] UBI: physical eraseblock size:   131072 bytes (128 KiB)  [    5.320000] UBI: logical eraseblock size:    126976 bytes  [    5.320000] UBI: smallest flash I/O unit:    2048  [    5.330000] UBI: VID header offset:          2048 (aligned 2048)  [    5.330000] UBI: data offset:                4096  [    5.480000] UBI: max. sequence number:       2  [    5.500000] UBI: attached mtd10 to ubi0  [    5.500000] UBI: MTD device name:            "rootfs0"  [    5.510000] UBI: MTD device size:            32 MiB  [    5.510000] UBI: number of good PEBs:        256  [    5.520000] UBI: number of bad PEBs:         0  [    5.520000] UBI: max. allowed volumes:       128  [    5.530000] UBI: wear-leveling threshold:    4096  [    5.530000] UBI: number of internal volumes: 1  [    5.540000] UBI: number of user volumes:     1  [    5.540000] UBI: available PEBs:             0  [    5.540000] UBI: total number of reserved PEBs: 256  [    5.550000] UBI: number of PEBs reserved for bad PEB handling: 4  [    5.560000] UBI: max/mean erase counter: 1/0  [    5.560000] UBI: image sequence number:  1113071030  [    5.560000] UBI: background thread "ubi_bgt0d" started, PID 80  UBI device number 0, total 256 LEBs (32505856 bytes, 31.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)  [    5.660000] UBIFS: mounted UBI device 0, volume 0, name "system"  [    5.660000] UBIFS: mounted read-only  [    5.660000] UBIFS: file system size:   30093312 bytes (29388 KiB, 28 MiB, 237 LEBs)  [    5.670000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)  [    5.680000] UBIFS: media format:       w4/r0 (latest is w4/r0)  [    5.690000] UBIFS: default compressor: zlib  [    5.690000] UBIFS: reserved for root:  0 bytes (0 KiB)  config core 'version'          # ROM ver          option ROM '2.8.12'          # channel          option CHANNEL 'release'          # hardware platform R1AC or R1N etc.          option HARDWARE 'R3'          # CFE ver          option UBOOT '1.0.2'          # Linux Kernel ver          option LINUX '0.1.12'          # RAMFS ver          option RAMFS '0.1.12'          # SQUASHFS ver          option SQAFS '0.1.12'          # ROOTFS ver          option ROOTFS '0.1.12'          #build time          option BUILDTIME 'Wed, 16 Mar 2016 14:13:36 +0800'          #build timestamp          option BUILDTS '1458108816'          #build git tag          option GTAG 'commit 17f50389a144da43f3858d508d9de41885282406'  mount: mounting proc on /proc failed: Device or resource busy  mount: mounting sysfs on /sys failed: Device or resource busy  [    6.450000] Raeth v3.0 (Tasklet,SkbRecycle)  [    6.450000]  [    6.450000] phy_tx_ring = 0x074a3000, tx_ring = 0xa74a3000  [    6.450000]  [    6.450000] phy_rx_ring0 = 0x07df0000, rx_ring0 = 0xa7df0000  [    6.450000] SMACCR1 -- : 0x00006409  [    6.450000] SMACCR0 -- : 0x8068a794  [    6.480000] ESW: Link Status Changed - Port0 Link UP  [    6.480000] CDMA_CSG_CFG = 81000000  [    6.490000] GDMA1_FWD_CFG = 20710000  - preinit -  Wed Mar 16 14:27:38 UTC 2016  - regular preinit -  [    6.660000] UBI: attaching mtd12 to ubi1  [    6.670000] UBI: physical eraseblock size:   131072 bytes (128 KiB)  [    6.670000] UBI: logical eraseblock size:    126976 bytes  [    6.680000] UBI: smallest flash I/O unit:    2048  [    6.680000] UBI: VID header offset:          2048 (aligned 2048)  [    6.690000] UBI: data offset:                4096  [    6.940000] UBI: max. sequence number:       73  [    6.950000] UBI: attached mtd12 to ubi1  [    6.960000] UBI: MTD device name:            "overlay"  [    6.960000] UBI: MTD device size:            54 MiB  [    6.970000] UBI: number of good PEBs:        432  [    6.970000] UBI: number of bad PEBs:         0  [    6.980000] UBI: max. allowed volumes:       128  [    6.980000] UBI: wear-leveling threshold:    4096  [    6.990000] UBI: number of internal volumes: 1  [    6.990000] UBI: number of user volumes:     1  [    6.990000] UBI: available PEBs:             0  [    7.000000] UBI: total number of reserved PEBs: 432  [    7.000000] UBI: number of PEBs reserved for bad PEB handling: 8  [    7.010000] UBI: max/mean erase counter: 1/0  [    7.010000] UBI: image sequence number:  1117162028  [    7.020000] UBI: background thread "ubi_bgt1d" started, PID 149  UBI device number 1, total 432 LEBs (54853632 bytes, 52.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)  [    7.070000] UBIFS: recovery needed  [    7.140000] UBIFS: recovery completed  [    7.150000] UBIFS: mounted UBI device 1, volume 0, name "data"  [    7.150000] UBIFS: file system size:   52187136 bytes (50964 KiB, 49 MiB, 411 LEBs)  [    7.160000] UBIFS: journal size:       2666496 bytes (2604 KiB, 2 MiB, 21 LEBs)  [    7.170000] UBIFS: media format:       w4/r0 (latest is w4/r0)  [    7.180000] UBIFS: default compressor: lzo  [    7.180000] UBIFS: reserved for root:  2464926 bytes (2407 KiB)  /lib/preinit.sh: line 1: jffs2_not_mounted: not found  /etc damaged, recovering /etc/./Wireless/mt7612/mt7612.dat  - init -  [    7.780000] ra2880stop()...Done  [    7.790000] Free TX/RX Ring Memory!  init started: BusyBox v1.19.4 (2016-03-16 14:06:55 CST)    Please press Enter to activate this console. rcS S boot: INFO: rc script run time limit to 65 seconds.  [    8.820000] tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.  [    8.830000] Disabling lock debugging due to kernel taint  [    8.870000] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE].  [    8.970000] Tuxera FAT 12/16/32 driver version 3014.1.24 [Flags: R/W MODULE].  [    9.030000] tun: Universal TUN/TAP device driver, 1.6  [    9.030000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>  [    9.060000] Mirror/redirect action on  [    9.320000] GRE over IPv4 tunneling driver  [    9.550000] ipt: xt_cgroup_MARK installed ok.  [    9.620000] ip_set: protocol 6  [    9.900000] sstack_init  [   11.190000] <-- RTMPAllocTxRxRingMemory, Status=0  [   11.200000] <-- RTMPAllocAdapterBlock, Status=0  [   12.740000] <-- RTMPAllocTxRxRingMemory, Status=0  [   12.760000] <-- RTMPAllocAdapterBlock, Status=0  [   12.760000] pAd->CSRBaseAddress =0xc1100000, csr_addr=0xc1100000!  [   12.770000] <dbg> MAC_CSR0=1986146304, RtmpChipOpsHook  [   12.780000] <dbg> dev idx = 1!  [   12.780000] <dbg> get_dev_config_idx pAd->MACVersion = 76623000, pAd->ChipID = 76120044  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: INFO: loading exist /etc/config/network.  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: #### Loopback configuration  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: config interface loopback  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ifname      lo  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option proto       static  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ipaddr      127.0.0.1  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option netmask     255.0.0.0  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: #### LAN configuration  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: config interface lan  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ifname      eth0.1  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option type        bridge  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option proto       static  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ipaddr      192.168.31.1  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option netmask     255.255.255.0  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: #### WAN configuration  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: config interface wan  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ifname      eth0.2  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option proto       dhcp  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: ### IFB interface for MiQoS  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: config interface ifb  Wed Mar 16 22:27:44 CST 2016 netconfig[406]: option ifname ifb0  Wed Mar 16 22:27:45 CST 2016 netconfig[406]: #### READY configuration  Wed Mar 16 22:27:45 CST 2016 netconfig[406]: config interface ready  Wed Mar 16 22:27:45 CST 2016 netconfig[406]: option proto    static  Wed Mar 16 22:27:45 CST 2016 netconfig[406]: option ipaddr   169.254.29.1  Wed Mar 16 22:27:45 CST 2016 netconfig[406]: option netmask  255.255.255.0  [   15.230000] Raeth v3.0 (Tasklet,SkbRecycle)  [   15.240000]  [   15.240000] phy_tx_ring = 0x05ea3000, tx_ring = 0xa5ea3000  [   15.240000]  [   15.240000] phy_rx_ring0 = 0x061e8000, rx_ring0 = 0xa61e8000  [   15.240000] SMACCR1 -- : 0x00006409  [   15.240000] SMACCR0 -- : 0x8068a794  [   15.260000] CDMA_CSG_CFG = 81000000  [   15.270000] GDMA1_FWD_CFG = 20710000  [   15.350000] device eth0.1 entered promiscuous mode  [   15.350000] device eth0 entered promiscuous mode  [   15.370000] br-lan: port 1(eth0.1) entering learning state  [   15.370000] br-lan: port 1(eth0.1) entering learning state  [   16.120000] <dbg> MAC_CSR0=1986146304, rtmp_asic_top_init  [   16.220000] Set_Bsd_Proc 7114 Bsd 0  [   17.370000] br-lan: port 1(eth0.1) entering forwarding state  [   19.350000] <==== rt28xx_init, Status=0  [   21.650000] device wl0 entered promiscuous mode  [   21.650000] br-lan: port 2(wl0) entering learning state  [   21.660000] br-lan: port 2(wl0) entering learning state  [   22.300000] Set_Bsd_Proc 6786 Bsd 0  [   23.660000] br-lan: port 2(wl0) entering forwarding state  [   23.890000] <==== rt28xx_init, Status=0  [   23.890000] 0x1300 = 00064320  [   25.420000] device wl1 entered promiscuous mode  [   25.430000] br-lan: port 3(wl1) entering learning state  [   25.430000] br-lan: port 3(wl1) entering learning state  [   27.430000] br-lan: port 3(wl1) entering forwarding state  Wed Mar 16 22:28:10 CST 2016 boot_check[3836]: INFO: Wireless OK  [   43.000000] tcpproxy_init, succeed!  rcS S calling: /etc/rc.d/S90xunlei boot: WARNING: EXITCODE=0, execute too slow, 22 >= 15: /etc/rc.d/S90xunlei boot  [   66.970000] Enabling Ralink HW NAT Module ...  [   66.980000] Ralink HW NAT Module Enabled!  [   83.220000] xqfp: forward hooks init success!  [   83.230000] xqfp:pre hooks init success!  [   83.230000] xqfp:extend init success!  [   83.240000] xqfp: module init success!  rcS S boot: INFO: rcS S boot timing 75 seconds.  Wed Mar 16 22:28:55 CST 2016 INFO: rcS S boot timing 75 seconds.  rcS S boot: system type(R3/2): SQUASH/3  Wed Mar 16 22:28:55 CST 2016 system type(R3/2): SQUASH/3  rcS S boot: ROOTFS: ubi0_0 on / type ubifs (ro,noatime,bulk_read,no_chk_data_crc,compr=zlib)  Wed Mar 16 22:28:55 CST 2016 ROOTFS: ubi0_0 on / type ubifs (ro,noatime,bulk_read,no_chk_data_crc,compr=zlib)  mknod: /dev/gpio: File exists  Wed Mar 16 22:28:56 CST 2016 boot_check[7860]: Booting up finished.  

Зaтeм былa уcтaнoвлeнa Developer-прoшивкa и oткрыт дocтуп пo SSH:



Дaлee я нeмнoгo увлeкcя :)
Кoрoчe гoвoря вce кoнчилocь тeм, чтo я зaпoрoл флeш-рoутeрa, нo oб этoм кaк-нибудь в другoй рaз (ибo тeмaтикa caйтa — oбзoры).

Итoг

Дo тoгo, кaк я зaпoрoл флeш я уcпeл нeкoтoрoe врeмя пoпoльзoвaтьcя рoутeрoм. Кoнeчнo кaртинa у мeня cлoжилacь нe пoлнaя, нo тeм нe мeнee: ecли вы нe coбирaeтecь ничeгo прoшивaть, вac уcтрaивaeт cкрoмныe 3 fast ethernet пoртa, a чтo тaкoe IPTV вы дaжe нe cлышaли — этoт рoутeр будeт xoрoшeй пoкупкoй!

Видeo-вeрcия aнбoкcингa:

Спacибo зa внимaниe!

(c) 2015 Источник материала.

Рекламные ссылки